How To Set Up A Genie Garage Door Keypad

Download Article

Download Article

Genie garage doors are known for their convenience and easy-to-utilize remotes. Unfortunately, this system becomes less simple when yous need to sync or resync your remote. If you have a wireless keypad, you may also need to recalibrate this device if it doesn't open up your garage door properly. With the push of a few buttons, you can reset either your Genie opener or wireless keypad in a matter of minutes.

1. one

   Press down the square button for 3-5 seconds. Push and concord the square "Plan Fix" push for at least 3 seconds. Keep holding the button until the circular LED is lit up. The ellipsoidal LED adjacent to the round LED volition so flash imperial.^[ane]

   • This puts your opener into Programming Mode, which allows you lot to reset the device.
   • The positions of your buttons may differ in certain Genie models. Some models have all of the LEDs and buttons in a single line, while others accept their buttons clustered in 1 spot with the LEDs underneath. In this case, the buttons will look a little unlike, only will nonetheless be marked with the same shapes.
   • Go on in heed that the opener is the boxed device attached to your garage ceiling, while the remote refers to the smaller, pocket-sized device with 1-2 buttons.

2. 2

   Select the round "Learn Code" button on any openers made betwixt 1995 and 2022. Discover the minor round LED and push labeled "Radio Signal" and "Learn Code" on older opener models. If your opener is paired with a receiver, then 1 of the buttons will bespeak a radio point of some type. Reset this fashion of opener by pressing and holding the "Learn Code" push button until the "Radio Point" LED begins flashing.^[2]

   • If you're uncertain nigh how to reset an older opener model, bank check Genie'south website to find the owner transmission and instructional guide for your specific model: https://store.geniecompany.com/pages/shop-past-model-number.

   Advert

3. three

   Push the remote button quickly. Choose i of the unlabeled rectangular buttons on your remote and press it one time. Once you've washed this, the oblong purple LED lite on the opener volition light upward as a solid royal and end blinking. For this part, it doesn't thing which push button you push. Merely brand sure you retrieve the button you lot pressed, every bit this volition be the push button that opens and closes your garage door.^[three]

   • If your device was made between 1995 and 1997, and so the remote button format volition look a little different. Apply the 2 curved, rectangular buttons on the top half of the remote to reset and reprogram the opener.

4. 4

   Press the remote button ii more times to reset the opener. Push down the same push button on your garage door remote. Look for both the ellipsoidal and circular LED to light upwardly blue before they switch off birthday. This calibrates the opener and syncs it with your remote control.^[iv] Once both LEDs switch colour and turn off, button the same button on your remote to close or open up your garage door.^[5]

   • At this point, the opener will be fully reset and synced with your new remote!

Advertizement

1. 1

   Discover the up/downward and plan keys and press them down for 5 seconds. Locate the button labeled "Program" on the peak of the wireless keypad, along with the up/down push button on the lesser. Printing down both of these buttons simultaneously for about v seconds. When it has been reset successfully, the LED on the keypad will blink twice, and the unabridged device will go dark.^[6]

   • Subsequently you lot do this, whatsoever pre-existing keypad lawmaking won't be able to open up upward the garage door.

2. 2

   Printing 3, five, and vii in succession afterward the opener is in programming way. Push down the square "Program Gear up" push on the opener for at to the lowest degree 3 seconds to get it into programming way. Button downwards the "3," "5," and "7" buttons in sequential gild on the wireless keypad to showtime the programming process. This is the default code for all Genie garage keypads that are notwithstanding using their mill settings.^[7]

3. 3

   Push the upwards/down button 3 times to open the garage door. Discover the up/down push on the keypad, located toward the bottom of the device. After y'all've pressed "357" into the keypad, slowly push the upward/down push until the garage door moves. To double check and see if the keypad has synced correctly, input "357" into the device once more and hit the up/down push. If the garage door opens or shuts, so you're good to go!^[8]

   • Consider irresolute your passcode once you've synced the keypad to your opener. Check the owner'due south manual for further instructions: http://overheaddoor.custhelp.com/ci/fattach/get/208328/0/filename/Genie_WKP_Keypad_Revised.pdf.

Advertising

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Ad

• You tin echo this process every bit needed if y'all have more than 1 garage door in your abode. It's possible to sync multiple doors to one remote, if you'd similar!^[9]

Thanks for submitting a tip for review!

Advertisement

• Whenever you're resetting a Genie garage door opener, you lot only have 30 seconds to finish each step before the device exits reprogramming manner.^[10]

Advertisement

About This Article

Thanks to all authors for creating a page that has been read 181,105 times.

Is this commodity up to date?

Source: https://www.wikihow.com/Reset-a-Genie-Garage-Door-Opener

Share this post